Machinery telematics:
what to measure and why.

Telematics collects a machine’s data and brings it to a screen: pressures, temperatures, hours, fuel and alarms. Here we explain what can be measured, how the data arrives, what each reading is for and where to start.

In short
  • Machinery telematics measures what’s happening to a machine and turns it into data: pressures, temperatures, voltages, starts, hours, fuel and fault codes.
  • The journey has six steps: gauges, control unit, upload or extraction, database, dashboard and alerts.
  • Start with the machines that cost you most when they stop and a few readings. Then extend it.

What machinery telematics is

It’s measuring what happens to a machine while it works and sending it to a system where you can see it remotely. It isn’t just knowing where it is or how many hours it has run: it’s knowing how it’s doing.

One thing to be clear on: telematics isn’t operating the machine remotely. You see what’s happening and get alerts. The machine is still operated by its operator.

What can be measured

It depends on each machine and what you need to know, but these are the usual readings:

GroupWhat’s measuredWhat it tells you
Engine and startingHours, RPM, load, start attempts, stops and idling.How much it really works and whether it struggles to start.
PressuresOil, hydraulic circuit, air and fuel.Leaks and wear that build up little by little.
TemperaturesEngine, coolant, oil and hydraulic.Whether it’s working outside normal limits.
ElectricalVoltages, battery and alternator.Faults that end in a machine that won’t start.
FuelLevel, consumption per hour and refuelling.What each machine burns and whether something doesn’t add up.
Use and alarmsLocation, status and fault codes.Where it is, what it’s doing and what’s failing.

A single reading says little. What’s useful is the trend: a pressure dropping slightly each week or a battery holding less and less.

How the data reaches your screen

It looks simple and it isn’t. There are six steps between the machine and your phone:

  1. Gauges. They take the signals on the machine. If the machine already provides them, we use those; if not, they’re fitted.
  2. Control unit. It receives the signals, processes, stores and sends them.
  3. Upload or extraction. Over the network when there’s coverage. Where there isn’t, data waits in storage or is extracted on site.
  4. Database. Specialised, holding each machine’s history.
  5. Dashboard. It shows the data in order, by machine, by site or however you need it.
  6. Alerts and decisions. Once the data is processed, what drifts stands out. You decide before it stops.

Alerts using manufacturer limits

This is where the real value lies. Limits are set by machine and by variable, the manufacturer’s or your own, and you’re warned when they’re passed: “yesterday at 10:32, oil pressure fell below the recommended minimum” or “if this continues, it may deteriorate”.

Everything is recorded with date and time. That also helps check how a hired machine was used or support a warranty claim. We explain it in machinery alerts and manufacturer limits.

Manufacturer telematics or your own system

Many modern machines already send data to their manufacturer’s platform. That works while you have one brand. With several, you end up checking one portal per brand and cross-checking nothing, and older machines are left out.

Your own system brings together in one dashboard what some already send and what has to be measured on the others.

Where to start

  1. Choose the machines that cost you most when they stop.
  2. Decide what you need to know: four or five well-chosen readings beat a hundred nobody looks at.
  3. Define the alerts: what counts as abnormal and who gets told.
  4. Extend it to more machines once you see what has helped.

Beyond the construction site

What we know best is civil works, tunnelling and mining machinery. But it adapts to other equipment: factory machinery, compressors, generators or pumps. We explain it in industrial IoT and sensors.

To see it applied to your fleet, see remote heavy machinery monitoring. To get more from your hours, read how to track heavy machinery hours.

Sound familiar? See how we solve it in remote machinery monitoring or tell us about your case directly.

Tell us about your case↗

Questions,
on the table.

Does telematics work on older machines?

Yes. If the machine doesn’t provide data, gauges and a control unit that collects it are fitted.

What if the machine works without coverage?

The control unit stores the data and sends it when there’s a connection. It can also be extracted on site.

Can telematics operate the machine remotely?

No. Telematics means seeing what’s happening and getting alerts. The machine is operated by its operator.